Plumber's Essentials: Your Key to Bathtub Installation
Plumber's Essentials: Your Key to Bathtub Installation
Blog Article
We've come across the article relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and concluded it made sense to write about it with you here.
Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is conveniently easily accessible, the project can relocate rapidly; if you need to open a wall surface to eliminate the old tub as well as place the new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as set in the new one. Make sure you have actually certified yourself for the job and also fit attempting it. As opposed to working with a service provider to take over a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you may require a specialist plumber to make tube links.
This post will certainly aid you set up a brand-new bath tub in your bathroom if you have actually already bought a new bathtub and do not require to change the plan of your previous water pipelines.
Your devices and also material checklist must comprise the following:
Preparing for the Installation
First of all, the sustaining frame provided with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to prevent stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be quite bothersome because of the restricted accessibility that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have actually been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wooden boards under its feet, place the bath tub in the needed position. The wood boards are valuable in uniformly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the bathtub up until the spirit level reviews degree.
To install taps, fit all-time low of the outermost versatile tap port to the appropriate supply pipe by making a compression join; then do the very same for the other faucet.
Turn on the supply of water and also check all joints and also new pipework for leakages and tighten them if essential. Fill up the bathtub as well as additionally inspect the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait until the bathtub has actually been utilized at the very least once as this will certainly settle it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making sure that the washers are in location in between the faucet and also the sink. Safeguard the faucet in place with the producer supplied backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The previous kind needs to be linked to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to fracture an inflexible seal, triggering the water to pass through the wall surface between the bath and the tiling, causing complications with moisture and possible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill up the tub with water before securing, to allow for the movement experienced when the tub remains in use. The sealant can fracture relatively early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly readily available on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about How to Install a Bathtub Yourself? Put feedback further down. We would be pleased to see your opinion about this blog posting. Hoping to see you back again in the future. Enjoyed our posting? Please share it. Let others locate it. Thank-you for taking the time to read it.
Solve it now, dial here! Report this page